Hey guys and girls

[Neilc]

Currently have a 2007 Z4 2.5si E85. Just upgraded stereo and speakers, front and rear strut braces, stainless exhaust, clear third brake like and deep dish alloys. Looking for rear cubby speakers grills in black if anyone has any for sale. In the process of fitting an induction kit as K and N etc don't make one for mine due to the maf sensor being mounted in in the airbox lid. Still looking to add air suspension and maybe a spoiler as well.

 

[Eddie Zedder]

Hello and .

 

[Shelly]

Hi and welcome from me too

 

[Antm72]

Hello and welcome from me in South Yorkshire.
Im sure @GazHyde has put together an induction kit that fits your car.

 

[DavidM]

Welcome from Ireland!

 

[t-tony]

Currently have a 2007 Z4 2.5si E85. Just upgraded stereo and speakers, front and rear strut braces, stainless exhaust, clear third brake like and deep dish alloys. Looking for rear cubby speakers grills in black if anyone has any for sale. In the process of fitting an induction kit as K and N etc don't make one for mine due to the maf sensor being mounted in in the airbox lid. Still looking to add air suspension and maybe a spoiler as well.

I fitted this on my 2003 3.0 a few weeks ago. It has a 90mm dia.

Tony.

ps. Apologies for no welcome Nelic, most remiss of me. I'm near Lincoln, where are you located?

 

[Grumps]

Hello from Mansfield.

 

[zedwheels]

Hello Neilc and to .org. from here in South Wales. You hav'nt said where abouts you are in the country! And its obligatory
to post up some photos of your steed.

 

[andyglym]

to the forum from West Cumbria.

 

[billz]

Welcome from a fellow Si owner albeit the 3.0. Pics are a must. What Deep dish Alloys have you gone for ? and what Stainless have you had. I have the Scorpion Exhaust on ours

 

[Bazza]

from me enjoy

 

[Neilc]

I fitted this on my 2003 3.0 a few weeks ago. It has a 90mm dia.
View attachment 50816
View attachment 50815

Tony.

ps. Apologies for no welcome Nelic, most remiss of me. I'm near Lincoln, where are you located?

Hi I'm in Middlesex,

The issue I'm having is the maf sensor as its moulded to the lid which is a pain in the bum. I think they changed the engines around 06 or 07 as there's no dipstick on mine either

 

[t-tony]

Yes, I recall Gaz having that issue, I seem to remember he used an alloy tube and attached the MAF sensor onto it.If you don't need to re use the original air box I'm sure you could cut the MAF sensor and surrounding piece out of the plastic and attach it to a silicone tube like I used?

Tony.

 

[Neilc]

Welcome from a fellow Si owner albeit the 3.0. Pics are a must. What Deep dish Alloys have you gone for ? and what Stainless have you had. I have the Scorpion Exhaust on ours

Picked these up on eBay and have just had them refurbished. Picking them up next week.
Thought I would be different so got Square exhaust made to fit so I get a nice pop in lower gears. Fitted dynamat and silent coat in the boot, doors, door cards, and front base speaker locations as well as the rear sub cubbie mounts. Adds a little weights but the doors aren't as tinny and it stops a bit of the exhaust noise inside as well

 

[Neilc]

Picked these up on eBay and have just had them refurbished. Picking them up next week.
Thought I would be different so got Square exhaust made to fit so I get a nice pop in lower gears. Fitted dynamat and silent coat in the boot, doors, door cards, and front base speaker locations as well as the rear sub cubbie mounts. Adds a little weights but the doors aren't as tinny and it stops a bit of the exhaust noise inside as well

Slightly better pic to see, fronts are 19 x 8.5 rears 19 x 9.5. Just deciding on on 265 35 or 30 for the rears and 235 40 or 35 on the front

 

[Neilc]

Hello Neilc and to .org. from here in South Wales. You hav'nt said where abouts you are in the country! And its obligatory
to post up some photos of your steed.

Hi thanks for the welcome, I'm in Middlesex about 15 mins from ace cafe

 

[billz]

If 19s then you will need to go 265/30 and 235/35 or your speedo will be out quite a bit

 

[Neilc]

Yes, I recall Gaz having that issue, I seem to remember he used an alloy tube and attached the MAF sensor onto it.If you don't need to re use the original air box I'm sure you could cut the MAF sensor and surrounding piece out of the plastic and attach it to a silicone tube like I used?

Tony.

Hi Tony,

I looked at that but the way its moulded there isn't a complete circle on the lid side to fit the hose on. Not sure if you can tell from the pic. Think I've got it sorted but will know when the bits turn up next week. Was looking for an air scoop to go behind the front grill to direct the air better as well.

 

[Neilc]

If 19s then you will need to go 265/30 and 235/35 or your speedo will be out quite a bit

Yeah speedo will be out about 1% according to this.

http://www.willtheyfit.com/index.ph...2=35&wheel_size=19&wheel_width=8-5&offset2=40

 

[t-tony]

Hi Tony,

I looked at that but the way its moulded there isn't a complete circle on the lid side to fit the hose on. Not sure if you can tell from the pic. Think I've got it sorted but will know when the bits turn up next week. Was looking for an air scoop to go behind the front grill to direct the air better as well.

That's something on my list too. My Ramair is tight up against the original air box feed on the front panel which means it gets everything that comes its way as mine is an "open ended" filter, so a bigger scoop behind the grille should hopefully increase the flow even more. It also sounds nice when you give it a boot full................................

View: https://www.youtube.com/watch?v=QjS5-Uv0PoM


Tony.

ps. When I get to remodelling the air scoop I will keep you posted mate.